image

6. Error Display


MESSAGE

ERROR

CAUSE

SOLUTION


IE


WATER INlET ERRoR

The water tap is closed.

Open the water tap.

The filter of the valve inlet is clogged.

Clean the filter of the valve inlet.

The valve inlet is an inferior product or broke down.

Change the valve inlet.

The water level sensor (sensor pressure) is an inferior product or broke down.

Change the water level sensor (sensor pressure).

The drain motor works during water supply.

Change the drain motor.

The PCB ASS’Y does not check the water level.

Change the pCb ASS’y.


oE


DRAIN ERRoR

The drain hose is kinked or clogged.

Clean and straighten the drain hose.

The drain motor is an inferior product.

Change the drain motor.

The valve inlet works during drain.

Change the valve inlet

The water level sensor is an inferior product .

Change the water level sensor.

The PCB ASS’Y does not check the water level.

Change the pCb ASS’y.


UE

UN-BALANCE ERRoR

The laundry is concentrated to one side of the drum during spin.

Rearrange the laundry.


lE


DooR opEN ERRoR

The Start/Hold button is pressed while the door is opened.

Close the door.

The switch door lock is an inferior product.

Change the switch door lock.

The PCB ASS’Y does not check the door lock.

Change the pCb ASS’y.


E1

Water level detection error

Water level is below reset or overflow is detected

Change the sensor pressure.


E2


oVER

floW ERRoR

The water is supplied continuously due to an inferior valve inlet.

Change the valve inlet.

The valve inlet is normal, but the water level sensor (sensor pressure) is inferior.

Change the water level sensor (sensor pressure).

The drain motor dose not work.

(The fan motor is an inferior product or broke down.)

Change the drain motor.


E3


fAN MoToR ERRoR

The fan motor does not work.

(The fan motor is an inferior product or broke down.)

Change the fan motor.

The PCB ASS’Y does not control the fan motor.

Check the connector or change the pCb ASS’y .


E4


lEAKAGE ERRoR

Water leaks from the tub or the hose drain.

Check the leak of the tub or the hose drain. Then change the tub or the hose drain.

The foreign matter is jammed in the drain bellows. (Non-pump model)

Remove the foreign matter in the drain bellows.


E5

HIGH VolTAGE ERRoR

The laundry is jammed between the gasket and the drum.

Rearrange the laundry.

The PCB ASS’Y is an inferior product.

Change the pCb ASS’y.


E6


EMG ERRoR

The laundry is jammed between the gasket and the drum.

Rearrange the laundry.

The motor is an inferior product.

Change the motor.

The PCB ASS’Y is an inferior product.

Change the pCb ASS’y.


image


MESSAGE

ERROR

CAUSE

SOLUTION


E7


DIRECTIoN

The motor spins into an opposite direction.

Change the PCB ASS’Y or the motor.

The motor hall IC is an inferior product or broke down.

Change the motor hall IC or the motor.


E8


MoToR ERRoR

The motor is not normally connected.

Check the connector of the motor.

The motor does not work.

(The motor is an inferior product or broke down.)

Change the motor.


E9

SENSoR pRESSURE ERRoR

The water level sensor is an inferior product.

Change the water level sensor.


H1


THERMISToR (TEMp. SENSoR) DRy ERRoR

The thermistor dry is an inferior product or broke down.

Change the thermistor dry.

The thermistor dry is not connected normally.

Check the connector of the thermistor dry.


H2


THERMISToR WASH ERRoR

The thermistor wash is an inferior product or broke down.

Change the thermistor wash.

The thermistor wash is not connected normally.

Check the connector of the thermistor wash.


H3


THERMISToR

DRy oVERHEATING ERRoR

The fan motor does not spin with the proper rpm. (The fan motor is an inferior product or broke down.)

Change the fan motor.

The thermistor dry is an inferior product or broke down.

Change the thermistor dry.


H4

THERMISToR WASH oVERHEATING ERRoR

The heater worked without the water in the tub.

Check the water level.

The thermistor wash is an inferior product or broke down.

Change the thermistor wash.


H5

WATER TEMp.

ERRoR

The water temp. is over 45°C in delicate & wool course.

Change the thermistor wash.


H6


HEATER WASH ERRoR

The heater wash dose not work.

(The water temp. doesn't rise over 2°C during 15min.)

Change the heater wash.


H7

HEATER DRy ERRoR

The heater dry dose not work.

(The water temp. doesn't rise over 3°C during 8min.)

Change the heater dry.


H8

HEATER WASH oVERHEATING ERRoR

The heater worked without the water in the tub.

Check the water level and the heater wash.


pfE


pUMp fIlTER ERRoR

The drain pump filter is clogged.

Clean the drain pump filter.

The drain pump does not work during spin.

Change the drain pump.

The large amount of detergent was used.

Use the proper amount of detergent.

The drain hose is placed higher than 1m above the floor.

Place the drain hose 1m below the floor